Level-mount LM50HDCC Manuel d'utilisateur télécharger pdf

Installation instructions

Fixed/Tilt Plasma/LCD Wall Mount

Model: FT65-03*, FT65B-CC*, ELLCDM-

07,ELLCDP-07, LM50CDM, DC50CDM,

LM60T, DC60T, LM65FT*, DC65FT*

DO NOT RETURN THIS PRODUCT TO THE STORE OR WEB

SITE YOU PURCHASED IT FROM!

IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS

MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING

DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL

OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY,

LEVEL MOUNT, DIRECTLY.

Dial 1 888 229 1459 or email us at CustomerSupport@

ElexaUSA.com any time of the day or night for a quick and

efficient solution to your problem.

Our trained Customer Service Department is open 24 hours

a day, 7 days a week, every day of the year and is prepared

to assist you in both English and Spanish.

Please also visit our Web Site at www.LevelMount.com

for assistance.

Features:

• Integrated Bubble Level

• Durable Steel Construction

• Easy 2 Piece Mounting

• Tilts up to 30 degrees

• Locking Lever

• Stud Finder Included

Mounting Equipment Included:

Bag REF Description QTY

1 A Phillips M4 x 12 Bolt 4

B Phillips M4 x 20 Bolt 4

C Phillips M4 x 30 Bolt 4

2 D Phillips M5 x 12 Bolt 4

E Phillips M5 x 20 Bolt 4

F Phillips M5 x 30 Bolt 4

3 G Phillips M6 x 12 Bolt 4

H Phillips M6 x 24 Bolt 4

I Phillips M6 x 35 Bolt 4

4 J Phillips M8 x 25 Bolt 4

K Phillips M8 x 40 Bolt 4

5 L M4/M5 Washer 4

M M4/M5 Spacer 4

5 N M6/M8 Spacer 4

1 O M4 Lock Washer 4

2 P M5 Lock Washer 4

3 Q M6 Lock Washer 4

4 R M8 Lock Washer 4

S 3’’ Hex Screw 6

6 T Hex Washer 6

U Concrete Anchor 6

V M5 x 48 Bolt 8

7* W M5 Hex Nut 8

X M5 Washer 8

Y L-Shape Bar Lock 2

8 Z Phillips screws M5 x 10 Bolt 4

AA M5 Hex Nut 2

BB M5 Butterfly Nut 2

Tools required for attachment to stud:

1/2’’ (12mm) Socket Wrench

Stud finder

Tools required for attaching to concrete:

Electric drill

1/2’’ (12mm) Masonry Bit

CAUTION:

Installer must make sure the LCD Wall Mount is proper-

ly and securely attached and that appropriate fasteners

are used. It is the responsibility of the installer to verify

that the mount is anchored properly to the wall.

PLEASE NOTE: THE MOUNT MUST BE ATTACHED

TO WOOD STUDS OR TO PROPERLY INSTALLED

ANCHORS IN CONCRETE. DO NOT MOUNT ONLY

TO DRYWALL.

Before installing, check to make sure all parts of the

mount are included.

Make sure all screws and bolts are tightened before

allowing Wall Mount to bear the full weight of the

LCD Display.

Attaching Wall Plate to Wooden Studs:

1a. Locate wall studs: Locate a proper place to mount by

using the included stud finder (Figure 1) It is recom-

mended that the center of the stud be used – and that

a nail be used to verify that a stud has been located.

The mount requires a minimum of two studs to ensure

proper and safe installation. The tilt arms will adjust

horizontally to the right and left up to 8 inches after

you determine the desired viewing location.

Attaching LevelMount to wall: Once the Wall Plate is

in the correct position on the studs, screw 1 Hex Screw

and 1 Hex Washer (P & Q) in the upper left mounting

hole of the Wall Plate into the stud. Do not screw too

tight until after all the screws are in. Drill pilot hole with

1/8 inch drill bit.

Using the Bubble Level as your guide (Figure 3, page

2), drive the 2nd screw into the opposite upper right

hand mounting hole of the Wall Plate. Now tighten

both screws, proceed to drive the remaining 2 screws

into the studs as seen in figure 2, page 1.

Figure 1

NOTE: Due to the weight of the LCD/Plasma TV’s, it is

necessary to mount the Wall Plate to at least 2 studs.

Attaching Wall Plate to Concrete:

1b. Attaching Wall Mount to concretel: Place the Wall

Plate at the height you want to install the Plasma/LCD

wall Mount. Mark the six holes you will be using for

concrete anchors (Figure 4). Utilize the built-in bubble

level to ensure proper mounting (Figure 3). Drill holes

for the concrete anchors using an electric drill with a

masonry bit (1/2’’ or 12mm (Figure 5). Drill into the wall

at least as deep as the screw is long (3 inches).

Insert the anchors into the holes and set them flush to

the wall by tapping them in with a hammer (Figure 6).

Once the Wall Plate is in the correct position on the

wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer

(P & Q)

in the upper left mounting hole of the

Wall Plate. Do not screw too tight until all the screws

are in.

Drive the 2nd screw into the opposite upper right hand

mounting hole of the Wall Plate, then proceed to drive

the remaining 4 screws into the concrete anchors as

seen in figure 2. Make sure all screws are tightened.

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

2. Selecting the Appropriate Hardware for your LCD/

Plasma: CAUTION: Select Bag 1-4, which most resem-

bles the hole side on the back of your LCD/Plasma.

Thread the bolts carefully into your LCD or plasma by

hand to determine which provided mount hardware

(correct diameter) is appropriate for installation. If you

feel resistance, remove the bolt immediately! Next

determine the correct length of the required bolt as

described in the following step.

*Bag 7 only included with models FT65-03, FT65B-CC,

LM65FT and DC65FT

**PLEASE NOTE: You will not use all of the hardware

included. Please see last page of the manual if your

Plasma or LCD needs extension arms.

Tilt

Arms

Wall Plate

Cord

Management

www.LevelMount.com

1-888-229-1459

Patents Pending

English

CAUTION

This wall mount was designed

specifically to hold LCD TV’s 34” - 65” and a maximum

weight of up to 200lbs.Using this product with a TV

heavier than the maximum weight may result in injury.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Installation instructions

Installation instructionsFixed/Tilt Plasma/LCD Wall Mount Model: FT65-03*, FT65B-CC*, ELLCDM-07,ELLCDP-07, LM50CDM, DC50CDM, LM60T, DC60T, LM65FT*, DC

Page 2

Fixation du support d’écran au téléviseur LCD ou plasma:PANNEAU ARRIERE PLATUn téléviseur plasma ou LCD avec un panneau arrière plat nécessite une vis

Page 3 - Using as a Fixed Mount:

Page 4

Fixation des bras d’extension :(Remarque : Non inclus pour certains modèles)4. Si vous disposez d’un téléviseur LCD ou plasma de grande taille, vous d

Page 5

Attaching Monitor Bracket to a LCD/Plasma with:FLAT BACK Plasma/LCDs with a flat back panel will require a shorter bolt. For a flat back Plasma/LCD th

Page 6

Page 7 - Como soporte fijo:

Attaching Extension Arms:(Note: Some models not included)4. If you have an oversized LCD/ Plasma TV, you may need to use the Extension Arms provided.

Page 8

Installation instructionsSoporte fijo para televisores de plasma/LCD. Modelos: FT65-03*, FT65B-CC*, ELLCDM-07,ELLCDP-07, LM50CDM, DC50CDM, LM60T, DC60

Page 9

Cómo fijar la placa del televisor al televisor de LCD o de plasma:PARTE TRASERA PLANALos televisores de respaldo plano utilizan pernos más cortos. En

Page 10

Page 11 - Utilisation du support fixe :

Cómo fijar los brazos de extensión:(Nota: No compatible con todos modelos)4. Si cuenta con un televisor de plasma/LCD demasiado grande, es posible que

Page 12

Installation instructionsSupport mural fixe/basculant pour télé-viseur LCD ou plasma - Modèles : FT65-03*, FT65B-CC*, ELLCDM-07,ELLCDP-07, LM50CDM, DC

Modèles reliés DC65FT | LM65FT | FT65B-03 | FT65-03 |

Commentaires sur ces manuels

Pas de commentaire

Level-mount LM50HDCC Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la télévision Level-mount LM50HDCC. Level Mount LM50HDCC User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés DC65FT | LM65FT | FT65B-03 | FT65-03 |

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la télévision Level-mount LM50HDCC